Kiwire 3.0 Administrator - Device & Controller Setup Guide
Kiwire 3.0 Administrator - Device & Controller Setup Guide
Cambium Networks Configuration for Kiwire Hotspot
Cambium Networks Configuration for Kiwire Hotspot
Prerequisites
Before integrating the controller with Kiwire, it is necessary that the controller and access point:
-
are connected to the Internet
-
are reachable on the network
-
have an IP address assigned to the a through DHCP or static
Note:
-
Kiwire-hostname or Kiwire-ip can be obtain by contacting our technical support for our cloud customer. For enterprise client the ip will be on premises Kiwire ip address.
-
Social network hostname list can be obtained from Social network whitelist guide
Part 1: Cambium cnMaestro configuration
-
Login to your Cambium cnMaestro controller
-
Go to WLANs > Configuration > AAA Servers
-
Authentication Server
-
Host: Kiwire-hostname or Kiwire-Ip
-
Secret: create a secret pass phrase
-
Port: 1812
-
Timeout: 3 seconds
-
Attempts: 1
-
-
Accounting Server
-
Host: Kiwire-hostname or Kiwire-ip
-
Secret: secret same as authentication server
-
Port: 1813
-
Timeout: 3 seconds
-
Attempts: 1
-
Accounting Mode: Start-Interim-Stop
-
Accounting Packet: ticked
-
Interim Update Interval: 1800 seconds
-
-
Advanced Settings
-
NAS-Identifier: AP MAC address with capital letters and colon
-
Dynamic Authorization: ticked
-
Dynamic VLAN: ticked
-
Called Station ID: AP-MAC:SSID
-
-
Omaya 3.0 Administrator > Quick Setup > Dashboard
Documentation
Ubiquiti Networks Documentation
EdgeRouter
EdgeRouter Getting Started
EdgeRouter – Beginners Guide to EdgeRouter
EdgeRouter – Which EdgeRouter Should I Use?
EdgeRouter – Packets Processing
EdgeRouter – Device LED Statuses
EdgeRouter – EdgeOS Feature Backends
EdgeRouter – SFP/SFP+ and DAC Compatibility List
EdgeRouter – Deep Packet Inspection Engine
EdgeRouter – How to Configure an Interface
EdgeRouter – Configuring Public Static IP Addresses
EdgeRouter – How to Add a Static Route
EdgeRouter – Configuration and Operational Mode
EdgeRouter – Copy and Replace Configuration Sections
EdgeRouter Configuration
EdgeRouter – WAN Load-Balancing
EdgeRouter – L2TP IPsec VPN Server
EdgeRouter – VLAN-Aware Switch
EdgeRouter – Policy-Based Site-to-Site IPsec VPN
EdgeRouter – Route-Based Site-to-Site IPsec VPN
EdgeRouter – Hardware Offloading
EdgeRouter – Source NAT and Masquerade
EdgeRouter – How to Create a WAN Firewall Rule
EdgeRouter – How to Create a Guest\LAN Firewall Rule
EdgeRouter – DNS Forwarding Setup and Options
EdgeRouter – DHCP Server Static Mapping
EdgeRouter – DHCP Server Using Dnsmasq
EdgeRouter – Built-in Dynamic DNS
EdgeRouter – Custom Dynamic DNS
EdgeRouter – Ubiquiti Device Discovery
EdgeRouter – Create Virtual Interfaces with VLAN IDs
EdgeRouter – Router on a Stick
EdgeRouter – Configure an EdgeRouter as a Layer 2 Switch
EdgeRouter – Interface Bonding
EdgeRouter – Creating a Bridged Interface
EdgeRouter – OpenVPN Site-to-Site
EdgeRouter – OpenVPN Layer 2 Tunnel
EdgeRouter – EoGRE Layer 2 Tunnel
EdgeRouter – Modifying the Default IPsec Site-to-Site VPN
EdgeRouter – Site-to-Site VPN Behind NAT
EdgeRouter – Dynamic Site-to-Site IPsec VPN using FQDNs
EdgeRouter – Site-to-Site IPsec VPN to USG
EdgeRouter – Site-to-Site IPsec VPN to pfSense
EdgeRouter – Site-to-Site IPsec VPN to Cisco ASA
EdgeRouter – Site-to-Site IPsec VPN to Cisco ISR
EdgeRouter – Site-to-Site IPsec VPN to Juniper SRX
EdgeRouter – Site-to-Site IPsec VPN with Many-to-Many Source NAT
EdgeRouter – Site-to-Site IPsec VPN with Many-to-One Source NAT
EdgeRouter – Route-Based Site-to-Site VPN to Azure (VTI over IKEv2/IPsec)
EdgeRouter – Route-Based Site-to-Site VPN to Azure (BGP over IKEv2/IPsec)
EdgeRouter – Policy-Based Site-to-Site IPsec VPN to Azure (IKEv1/IPsec)
EdgeRouter – Route-Based Site-to-Site VPN to AWS VPC (BGP over IKEv1/IPsec)
EdgeRouter – Route-Based Site-to-Site VPN to AWS VPC (VTI over IKEv1/IPsec)
EdgeRouter – How to Distribute Public IP Addresses
EdgeRouter – How to Create a Firewall Rule Using DPI
EdgeRouter – Reordering Firewall and NAT Rules
EdgeRouter – Add Commands to EdgeOS
EdgeRouter – Run Operational Mode Command from Scripts
EdgeRouter – IPv6 Tunnel Broker
EdgeRouter – Remote Syslog Server for System Logs
EdgeRouter – Virtual Router Redundancy Protocol (VRRP)
EdgeRouter – Border Gateway Protocol (BGP)
EdgeRouter – Policy-Based Routing
EdgeRouter – Zone-Based Firewall
EdgeRouter – Root User Account
EdgeRouter – Custom DHCP Server Options
EdgeRouter – UAP Controller DHCP Options
EdgeRouter – How to Disable IPv4 Offloading (Hardware Acceleration)
EdgeRouter – Add Debian Packages to EdgeOS
EdgeRouter – Quality of Service (QoS) Advanced Queue
EdgeRouter – Quality of Service (QoS)
EdgeRouter – Quality of Service (QoS) Shaper for Upload/Download and VoIP
EdgeRouter – Virtual Private LAN Service (VPLS) with LDP Signaling
EdgeRouter – PPPoE Server Rate Limiting Using WISPr RADIUS Attributes
(ARCHIVED) EdgeRouter – PPPoE RADIUS Disconnect Daemon
(ARCHIVED) EdgeRouter – Sample Scripts to Change the Configuration
(ARCHIVED) EdgeRouter – Ad-blocking (content filtering) using EdgeRouter
(ARCHIVED) EdgeRouter – Legacy WAN Load-Balancing with Policy-Based Routing
EdgeRouter System Management
EdgeRouter – How to Upgrade the EdgeOS Firmware
EdgeRouter – How to Connect to Serial Console
EdgeRouter – How to Update the Bootloader
EdgeRouter – Backup and Restore Configuration
EdgeRouter – Backing Up the Config Directory
EdgeRouter – How to Access the EdgeRouter
EdgeRouter – Access the CLI from the Web UI
EdgeRouter – Adjusting System Log Size
EdgeRouter – Capturing Packets
EdgeRouter – Enable the Telnet Service
EdgeRouter – Displaying the CPU Temperature
EdgeRouter – Archiving and Managing the Configuration Files
EdgeRouter – Uploading Files using SCP
EdgeRouter Troubleshooting
EdgeRouter – Manual TFTP Recovery
EdgeRouter – Reset to Factory Defaults
EdgeSwitch & EdgeSwitch X
EdgeSwitch & EdgeSwitch X – How to Upgrade the Firmware
EdgeSwitch & EdgeSwitch X – UNMS Adoption
EdgeSwitch & EdgeSwitch X – Device LED Statuses
EdgeSwitch & EdgeSwitch X – How to Enable PoE Output
EdgeSwitch & EdgeSwitch X – How to Reset to Factory Defaults
EdgeSwitch & EdgeSwitch X – Backup and Restore the Configuration
EdgeSwitch & EdgeSwitch X – Network Management Interface
EdgeSwitch & EdgeSwitch X – How to Add VLANs
EdgeSwitch & EdgeSwitch X – Tagging and Untagging Port VLANs
EdgeSwitch & EdgeSwitch X – Link Aggregation Groups (LAG)
EdgeSwitch & EdgeSwitch X – Port Isolation
EdgeSwitch & EdgeSwitch X – Verify SFP/SFP+ Modules
EdgeSwitch & EdgeSwitch X – SFP/SFP+ Interface Options
EdgeSwitch & EdgeSwitch X – Verifying Blocked STP Ports
EdgeSwitch & EdgeSwitch X – How to Sanitize the Configuration
EdgeSwitch – Inter-VLAN Routing
EdgeSwitch – Limiting Inter-VLAN Routing with Access-Lists
EdgeSwitch – How to Update the Bootloader
EdgeSwitch – Configuration and Administration Guides
EdgeSwitch – How to Connect to Serial Console
EdgeSwitch – Management Access Methods
EdgeSwitch XP
EdgeSwitch XP – How to Reset to Factory Defaults
EdgeSwitch XP – How to Upgrade the Firmware
EdgeSwitch XP – How to Add VLANs
EdgeSwitch XP – Enable Passive PoE Output
EdgeSwitch XP – Support for Quality of Service (QoS)
EdgeSwitch XP – Access and Manage the ES-16XP
EdgeSwitch XP – Enable Passive PoE Output using the Command Line