top of page

Kiwire 3.0 Administrator      >        Setting up the Wi-Fi Hardware & Configuration       >       Nomadix   

Kiwire 3.0 Administrator - Device & Controller Setup Guide

Nomadix Configuration for Kiwire

This guide shows how to configure a Nomadix device with Kiwire. The test below is based on AG 5900 v8.14.018. A. Nomadix AG 5900 Configuration

nomadix_kiwire_01_01.jpg

Step 1 – Create the Radius Profile.
 

  • Go to Configuration > Realm-Based Routing and create a new RADIUS Service Profile.

  • Enable RADIUS Authentication Service: Enable

  • Protocol: PAP

  • Primary IP / DNS: IP Address of Kiwire; Port: 1812; Secret Key: shared secret key

  • Enable RADIUS Accounting Service: Enable

  • Primary IP / DNS: IP Address of Kiwire; Port: 1813; Secret Key: shared secret key

nomadix_kiwire_02_02.jpg

Step 2 – RADIUS client setting.
 

  • Go to Configuration > RADIUS Client

  • Default RADIUS Mode: Fixed

  • Default RADIUS Service Profile: Select RADIUS Service Profile created in step 1

  • Under Miscellaneous Options, enable below:

nomadix_kiwire_02_03.jpg

Step 3 – Enable URL Redirection.
 

  • Send NAS identifier

  • NAS Identifier: value is specified in the Configuration > Summary, WAN MAC Address (WAN). In this example, the value is 0050E804394C

nomadix_kiwire_03_04.jpg

Step 4 – Send Framed IP.
 

  • Enable Termination-Action Radius Attribute

  • Enable Goodbye URL

nomadix_kiwire_03_05.jpg

Step 5 – Enable the AAA service.
 

  • Go to Configuration > AAA. Under Options tab, configure as below:

  • Logout IP: 2.2.2.3 or 3.3.4.5 or 4.5.6.7 or 5.0.0.5

  • Configure the XML Interface. Enable Authentication via XML and via IP Address

  • XML SERVER 1 IP: IP Address of Kiwire

  • HTTPS Redirection: Enable

Step 6 – Go to Configuration > AAA. Under Internal Web Server Tab, configure as below:
 

  • Enable Portal Page

nomadix_kiwire_04_06.jpg
nomadix_kiwire_04_07.jpg

Step 7 – Enable Passthrough Addresses
 

  • Go to Configuration > Passthrough Addresses, add IP/DNS Name for white lists

Nomadix_1.png

Step 8 – Enable VLAN

​

  • Go to Configuration > Port-Location

  • Enable VLAN IDs: 802.1Q two-way

nomadix_kiwire_05_08.jpg

Go to Port-Location, Add a Port Location. In this example, we are going to create VLAN200 using Subnet 192.168.200.0:

nomadix_kiwire_05_09.jpg

Step 9 – Create DHCP for VLAN
 

  • Go to Configuration > DHCP and add a new DHCP Pool.

nomadix_kiwire_06_10.jpg

Kiwire Configuration for Nomadix controller
 

Adding NAS into Kiwire

​

  1. Navigate to Devices > Devices > Add Device

  2. Device Type → Controller

  3. Vendor → Nomadix xml

  4. Identity → Same value as NAS id set in NAG but with lower case letter

  5. Ip Address → Ip address of nomadix wan

  6. Address → optional

  7. Shared Secret Key → Secret key phrase set at Radius

  8. Username → NAG username

  9. Passowrd → NAG password

  10. COA Port → 3799

  11. Description → optional

  12. Monitoring Method → optional

  13. Community → optional

  14. Snmp version → optional

bottom of page